Survey Instruments
Concrete testing instruments
Soil testing instruments
Structural Analysis Laboratory
Construction Calculators
 
Structural Analysis Laboratory
 
Apparatus For Verification of Clerk's Maxwell Reciprocal Theorem
Specification:-
Apparatus consists of a beam 100cm long and 1.25 cm x 4 mm in cross section with graduations at every 10cm along the length. It is supported on two knife edge supports 70cm apart with a 30cm overhang on one side. Reciprocal theorem can be verified by direct measurements of the deflections of various points with the help of a dial gauge due to a load placed at the reciprocal points. A dial gauge, supporting stand and a set of weights is supplied with the apparatus..
 
 
Elastic Properties of Deflected Beam Apparatus
Specification:-
Verification of moment Area theorem for slopes and deflection of the beam. Apparatus consists of a mild steel beam 2.5cm x 3 mm in cross section and 100cm long, pinned to two supports 70cm apart situated symmetrically. Vertical loads can be applied at various points along the span of the beam. A dial gauge is supplied with the apparatus & a supporting stand and a set of weights.
 
 
Deflection of Truss Apparatus
Specification:-
Apparatus consists of 4 panels of a PRATT truss, each panel being 40cm in horizontal direction and 30cm in vertical direction. All tension members are provided with detachable springs so as to obtain appreciable deformation of the member. Apparatus can be used to illustrate visually the nature of forces set up in various members of the Truss. Apparatus is supplied complete with a supporting stand and a set of weights.
 
 
Curved Member Apparatus
Specification:-
Apparatus consists of a steel bar which is used to make the different cur members Viz. circle, semicircle with straight arm, a quadrant of a circle and quadrant of a circle with straight arm. The bottom ends of the members are fixed to the base. Under the application of load at free end, its horizontal and vertical deflection is measured with the help of dial gauges. A dial gauge, supporting stand & a set of weights is supplied with the apparatus.
 
 
Three Hinged Arch Apparatus
Specification:-
The model has span of 100cm and rise 25cm, with hinges at supports and crown. One of the ends rests on rollers. Along the horizontal span of the arch various points are marked at equidistant for the application of load. A dial gauge, a supporting stand and a set of weights is supplied with the apparatus.
 
 
Behavior of Column and Struts Apparatus
Specification:-
Apparatus consists of four spring steel columns which are put along a vertical wooden board. These four columns have different end conditions as below:
1. Both ends pinned
2. Both ends fixed
3. One end pinned and other fixed
4. One end fixed and other end free
Apparatus is supplied complete with a supporting stand and a set of weights.
 
 
Two Hinged Arch Apparatus
Specification:-
The model has a span of 100cm and rise 25cm. Both ends are hinged but one of the ends is also free to move longitudinally. A lever arrangement is fitted at this end for the application of known horizontal inward force for measuring the horizontal thrust. Along the horizontal span of the arch various points are marked at equidistant for the application of load. This being a statically indeterminate. structure of the first degree. A dial gauge, supporting stand and a set of weights is supplied with the apparatus.
 
 
Pin Joint Truss Apparatus
Specification:-
Apparatus consists of three suspension members (spring balances) of different stiffness which are jointed at a point to form the redundant joint. The upper end of the suspension members being tied in a position to a vertical wooden board. Two dial gauge, supporting stand and a set of weight are supplied with the apparatus.
 
 
Unsymmetrical Bending Apparatus
Specification:-
Cantilever beam of length 80cm is tied in the apparatus. The beam is fixed at one end such that the rotation of 450 intervals can be given and clamped such that the principal axis of its cross-section may be inclined at any angle with the horizontal and vertical planes . Also arrangement is provided to apply vertical load at the free end of the cantilever and to measure horizontal and vertical deflection of the free end. A dial gauge, supporting stand and a set of weights is supplied with the apparatus.
 
 
 
Contact us
Contact Person : Mr. Azeem Ahmed
Office : C-4(E), Ramnagar Industrial Estate, Roorkee (Uttarakhand) - 247667
Mobile : +91 - 9997922618
Email : info@averexinstruments.com
Queck query
Home  |  Company Profile  |  Our Products  |  Download Catalogue  |  Contact Us  |  Enquiry  |  Email Us
Copyright © Nexus Technologies. All Rights Reserved.
Website Developed & Maintained by True Value SEO